Bakelite Series

INTRODUCTION

Motor Start Capacitors are commonly used in single-phase mofors to boost the value of their starting forque. It is necessary that the start should take in a small fraction of time (seconds) with the input of a high reactive power.

Due to its advantages like size and high capacitance value, the motor start capacitor is the best capacitor for this type of application. Once the mofor has been started, the capacitor should be disconnected from the circuit. The capacitor elements are made out of aluminum foil separated by layers of impregnated paper.

VENT TEST

Capacifors shall be capable of releasing any excessive internal pressure without violent expulsion of capacitor element or cover or emission of flame,when rated AC RMS voltage 60 Hz is applied continuously to a capacitor.

Care should be taken to shield the capacitor from observers to prevent injury.

ACCELERATED LIFE TEST

Capacitors shall be capable of withstanding life test conditions per ElA 463-B in a 65*C ambient at rated sinusoidal voltage and frequency with current Imiting and discharge resistors.

A resistance equivalent to approximately 10% of the capacitor impedance shall be connected in series with each capacitor and a resistor of approximately 1000 ohms shall be connected in parallel with each capacitor.

Life fest shall be conducted in a test chamber with capacitors separated by at least I inch of air and with sufficient circulation so that the ambient temperature remains within the above temperature limits and does not vary more than I'C. Also, capacitors shall not be exposed to direct radiation from heating elements. Test voltage is applied to the capacitor resistor combination. At the conclusion of the life test, at room femperature, the capacitance shall not differ from the initial measured value by more than +25% and the power factor shall not exceed 20%.

Electrical Specifications

Capacitance Range	25~1536MFD
Voltage Ratings	110, 125, 165, 220, 250, 330VAC
Capacitance Tolerance	-0~+20%
Rated Frequency	50/60 Hz
Operating Temperature	-20+65%C max, 70°C Upon request
Power Factor	8%

Mechanical Specifications

Case: Phenolic or Thermoplastic case with a positive pressure safety vent.

Terminals: Designed to accept 1/4" ; single,

double and triple quick female connectors with solder lug option.

Marking: Manufacturer identilication, capacitance range, rated voltage, working frequency,

maximum operating temperature, manufacture week; year, and UL marking.

(Special marking available on request.)

Shell size

D	37Ø	40Ø	46Ø	51Ø
L	70mm	80mm	86mm - 106mm	100mm- 116mm
F	11	11	15	15
H max	2	2	0.5	1

Shell size comparison table (Asian version) ASIA

VOLTAGE	110V	125V	165V	220V	250V	330V
CAPACITANCE VALUE	size m/m	size m/m	size m/m	size m/m	size m/m	size m/m
25 - 30	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70
30 - 36	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70
36 - 43	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70
43 - 52	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70
53 - 64	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70	40 x 80
64 - 77	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70	40 x 80
72 - 86	37 x 70	37 x 70	37 x 70	37 x 70	37 x 70	40 x 80
88 - 106	37 x 70	37 x 70	37 x 70	37 x 70	40 x 80	46 x 86
108 - 130	37 x 70	37 x 70	37 x 70	37 x 70	40 x 80	46 x 86
124 - 149	37 x 70	37 x 70	37 x 70	40 x 80	40 x 80	40 x 106
130 - 156	37 x 70	37 x 70	37 x 70	40 x 80	40 x 80	40 x 106
145 - 174	37 x 70	37 x 70	37 x 70	40 x 80	40 x 80	40 x 106
161 - 193	37 x 70	37 x 70	40 x 80	40 x 80	46 x 86	40 x 106
189 - 227	37 x 70	37 x 70	40 x 80	40 x 80	46 x 86	51 x 116
216 - 259	37 x 70	40 x 80	40 x 80	46 x 86	46 x 86	51 x 116
233 - 280	37 x 70	40 x 80	40 x 80	46 x 86	46 x 86	51 x 116
243 - 292	40 x 80	40 x 80	46 x 86	46 x 86	46 x 86	51 x 116
270 - 324	40 x 80	46 x 86	46 x 86	46 x 86	40 x 106	51 x 116
324 - 389	40 x 80	46 x 86	46 x 86	40 x 106	40 x 106	51 x 116
340 - 408	46 x 86	46 x 86	46 x 86	40 x 106	40 x 106	51 x 116
378 - 454	46 x 86	46 x 86	46 x 86	40 x 106	40 x 106
400 - 480	46 x 86	46 x 86	40 x 106	40 x 106	40 x 106
430 - 516	46 x 86	40 x 106	40 x 106	40 x 106	40 x 106
460 - 552	46 x 86	40 x 106	40 x 106	40 x 106	40 x 106
540 - 648	40 x 106	40 x 106	40 x 106	40 x 106	40 x 106
590 - 708	40 x 106	40 x 106	40 x 106	40 x 106	40 x 106
645 - 774	40 x 106	40 x 106	40 x 106	51 x 116	51 x 116
708 - 850	40 x 106	40 x 106	40 x 106	51 x 116	51 x 116
720 - 864	40 x 106	40 x 106	51 x 116	51 x 116	51 x 116
800 - 960	40 x 106	40 x 106	51 x 116	51 x 116	51 x 116
815 - 978	40 x 106	40 x 106	51 x 116	51 x 116	51 x 116
829 - 995	40 x 106	40 x 106	51 x 116	51 x 116	51 x 116
850 - 1020	40 x 106	51 x 116	51 x 116	51 x 116	51 x 116
1000 - 1200	40 x 106	51 x 116	51 x 116	51 x 116	51 x 116
1020 - 1224	40 x 106	51 x 116	51 x 116	51 x 116	51 x 116
1175 - 1410	40 x 106	51 x 116	51 x 116	51 x 116	51 x 116
1280 - 1536	40 x 106	51 x 116	51 x 116	51 x 116	51 x 116

Shell size comparison table (European and American version) EUR.& USA.

VOLTAGE	110V	125V	165V	220V	250V	330V
CAPACITANCE VALUE	size m/m	size m/m	size m/m	size m/m	size m/m	size m/m
25 - 30	37 x 70	37 x 70	40 x 80	40 x 80	40 x 80	40 x 80
30 - 36	37 x 70	37 x 70	40 x 80	40 x 80	40 x 80	40 x 80
36 - 43	37 x 70	37 x 70	40 x 80	40 x 80	40 x 80	40 x 80
43 - 52	37 x 70	37 x 70	40 x 80	40 x 80	40 x 80	40 x 80
47 - 56	37 x 70	37 x 70	40 x 80	40 x 80	40 x 80	40 x 80
53 - 64	37 x 70	37 x 70	40 x 80	40 x 80	46 x 86	46 x 86
64 - 77	37 x 70	37 x 70	40 x 80	40 x 80	46 x 86	40 x 106
72 - 86	37 x 70	37 x 70	40 x 80	40 x 80	46 x 86	40 x 106
88 - 106	37 x 70	37 x 70	40 x 80	40 x 80	40 x 106	40 x 106
108 - 130	37 x 70	37 x 70	40 x 80	40 x 80	40 x 106	40 x 106
124 - 149	37 x 70	37 x 70	40 x 80	40 x 80	40 x 106	40 x 106
130 - 156	37 x 70	37 x 70	40 x 80	40 x 80	40 x 106	40 x 106
145 - 174	37 x 70	37 x 70	40 x 80	40 x 80	40 x 106	51 x 116
161 - 193	37 x 70	37 x 70	40 x 80	40 x 80	40 x 106	51 x 116
189 - 227	37 x 70	40 x 80	40 x 80	46 x 86	40 x 106	51 x 116
216 - 259	37 x 70	40 x 80	40 x 80	46 x 86	40 x 106	51 x 116
233 - 280	37 x 70	40 x 80	46 x 86	40 x 106	40 x 106	51 x 116
243 - 292	46 x 86	46 x 86	40 x 106	40 x 106	40 x 106	51 x 116
270 - 324	46 x 86	46 x 86	40 x 106	40 x 106	51 x 116	51 x 116
324 - 389	46 x 86	46 x 86	40 x 106	40 x 106	51 x 116
340 - 408	46 x 86	46 x 86	40 x 106	40 x 106	51 x 116
378 - 454	46 x 86	46 x 86	40 x 106	40 x 106	51 x 116
400 - 480	46 x 86	40 x 106	40 x 106	51 x 116	51 x 116
430 - 516	40 x 106	40 x 106	40 x 106	51 x 116	51 x 116
460 - 552	40 x 106	40 x 106	40 x 106	51 x 116	51 x 116
540 - 648	40 x 106	40 x 106	40 x 106	51 x 116	51 x 116
590 - 708	40 x 106	40 x 106	40 x 106	51 x 116
645 - 774	40 x 106	40 x 106	40 x 106	51 x 116
708 - 850	40 x 106	40 x 106	40 x 106
720 - 864	40 x 106	40 x 106	40 x 106
800 - 960	40 x 106	40 x 106	51 x 116
815 - 978	40 x 106	40 x 106	51 x 116
829 - 995	40 x 106	40 x 106	51 x 116
850 - 1020	40 x 106	51 x 116	51 x 116
1000 - 1200	40 x 106	51 x 116	51 x 116
1020 - 1224	51 x 116	51 x 116
1175 - 1410	51 x 116	51 x 116
1280 - 1536	51 x 116	51 x 116

ㆍAbove case dimensions are based on our standard design and might be altered without notice.

ㆍ Requirements of special specifications can be designed at request.

TERMINAL CODE-Phenolic Case

Recommend

Aluminum Shell Series

Electrolytic Motor starting capacitors are made of aluminium foils and separated by a leaf of impregnated paper as the electrolyte.

They are normally used in singe phase induction motors in order to increase the value of the starting torque.

P03B Series

MAINLY MARKING

LAI	- P/N-
MPP CAPACITOR	- Style
CAP XX UF	- CAP.
WY XXX Y.AC	- Vol.
-XX°C ~ +XX°C	- Temperature